Bracelet with Bouquet of Roses

I always told you.. rose is my favourite flower. Girls... here is a good DIY idea for you by Rusalina.

It's no secret that the Rose - the queen of flowers. Woman walking with a bouquet of roses - captivating and affectionate, she attracts the attention and holds the views of both men and women. Unfortunately, it is impossible to walk daily with a bouquet of fresh flowers, but the attention and admiration always want to feel. I propose to make their own hands a bouquet of roses, which not only does not fade, but will still give you pleasure for years to come.

Materials that are necessary for moulding: polymer clay of three colours: white, red and green; nail polymer clay. Tools and supplies that are necessary for moulding: ceramic tile or glass, toothpick or a needle, stationery knife or blade, cutter in the shape of a star, small size, small scissors.

Before the start of moulding plastic mash thoroughly, otherwise we will not get thin petals. Begin to knead the clay with the lightest colours, gradually moving to darker.

Before moulding roses need to mix part red plastic with white, to obtain an intermediate light-red hue. So: we need less red three times in volume than light red, but white plastic need four times more than red.

Red polymer clay will go to a flower core. Pinch off a piece of red clay, about the size of a pea, and form of his tear drop shape.

Puts a drop in the middle of the palm, pre-lubricated hand cream or moistened with water - it is necessary to ensure that plastic does not stick to the skin.

Presses his thumb, and drop without lifting your finger, stretch the left to the right plastic. Thus, we get flattened elongated petal.

Disconnect from the palm petal recommend the top, just slightly bent away the upper part, while the tab will not be disconnected from the palm of your hand.

For one full rose flower we will go: one red petal, three light red and four white. Number of roses for bracelet - from 9 to 13 pieces.

Red petal, which will serve as the core, turn spiral.

Around the red petals laid three light red, slightly overlapping each other.

The last stage of the four white petals, laid in a similar manner - slightly overlapping the previous tab. Using toothpick or nail edges Give flower light waviness and bends.

We stayed roses tail to be cut. Make it any small scissors.

When the stuff is made of rose - send them in the first baking in the oven. Observe strict time and temperature baking, as recommended on the package.

While baked roses begin to stalk and leaves. On average mode pasta machine or rolling pin roll out a layer green colour. Cutter in the form of stars cut out as many forms as you roses.

A needle or toothpick, a slight pressure on the surface of the stars of plastic to put the finishing touches simulating streaks on fruit stems.

Let cool rose - this can be done by throwing them into the cold water after baking.

Fasten the stalk to flower roses. You can place the clutch fluff liquid gel, but I miss the item because light green plastic area is large and it is good to mate with a rose. After a well-stuck light green stalk to the base of the rose - you need a needle or toothpick to make a through-hole in the light green stalk, such as shown in the figure.

Leaves do with the help of mould and if there is a purchase - use it, and if not - you can use a self-made. To learn how to make a home made MDL I told in the lesson "Mould with their hands" (refer to lesson with Mould). If not available Mould - use live leaf, attach it to the plastic, rolled over it with a rolling pin and carve according to fingerprint. To plastic does not stick to Mould moisten it with water each time, or place it on the surface of the plastic wrap, and then Apply a light green plastic and roll the rolling pin.

To give relief form the edges of the leaves can be curly or wavy blade to make cuts with scissors.

Do not forget to make holes in the leaves before baking. Now the leaves and roses with the stem are ready to go into the oven for baking.

After baking is essential to degrease the surface of products and cover them with lacquer.

Assembly is as follows: in the roses and leaves holes inserted connecting rings and fastened to the chain links in the following order: two leaf - a flower - leaf, two - one flower, etc. Fasten snap hook or clasp Toggle on the final links in the chain. The bracelet is ready.